Shandong Zhongjie Special Equipment (formerly Heze Boiler Factory Co., Ltd.) was established in 2001, located at No. 2218 Jinnan Road, Development Zone, Heze City, with a registered capital of 50 million yuan and total assets of 500 million yuan. The company has 7 business centers: boilers, deep-freeze containers, pressure vessels, central air conditioning, engineering installation, international trade, and the Internet of Things. It has three factory sites on Jinnan Road, East Changjiang Road, and Bohai Road, covering a total area of 200,000 square meters, with the main workshop spanning 83,000 square meters. It currently employs 710 staff, including 247 engineers and technicians and 82 intermediate-level technicians. In December 2016, it was recognized as a "High-tech Enterprise" by the Science and Technology Department. In June 2021, it was identified as a "Specialized and New Enterprise in Shandong Province" by the Ministry of Industry and Information Technology. In June 2022, it was recognized as a "Gazelle Enterprise in Shandong Province" and in August 2022, it was identified as a "Specialized and New Small Giant Enterprise" by the Ministry of Industry and Information Technology.
The key to maintaining a hot water boiler is regular maintenance and inspections. Here are some common maintenance steps and precautions: Clean the burner and flue: Regularly clean the burner and flue to remove ash and dirt, maintaining combustion and heat exchange efficiency. Use cleaning tools and equipment as per the manual. Check water level and pressure: Regularly inspect the water level and pressure of the hot water boiler to ensure safe operation within the specified range. Top up water and adjust pressure to avoid issues caused by low or high water levels. Inspect water quality: Regularly conduct water quality tests to check hardness, alkalinity, oxygen content, and other indicators. Take appropriate water treatment measures based on test results, such as descaling and supplementing missing chemicals, to prevent scale and corrosion damage to the boiler. Check safety devices: Regularly inspect the safety devices of the hot water boiler, including safety valves, pressure switches, and water level controllers, to ensure normal operation and safe boiler operation. Inspect the electrical system: Regularly check the electrical system of the boiler, including power connections, controllers, and sensors, to ensure the normal operation of electrical equipment and avoid electrical faults. Regularly drain: Regularly drain the wastewater and impurities from the boiler to avoid their impact on the boiler. Develop a reasonable drainage plan based on the boiler's usage and water quality conditions. Keep records and monitor: Record the boiler's operating parameters, maintenance records, and fault situations, and regularly monitor and analyze them to identify and address issues promptly. Train operators: Ensure that operators are adequately trained.

When using a gas heat transfer oil furnace, the following points should be noted: - Safe Operation: A gas heat transfer oil furnace is a high-temperature equipment, and safety must be observed during operation. Operators should be familiar with the equipment's operation procedures and safety precautions, wear necessary personal protective equipment, and ensure safe operation. - Gas Supply: A stable gas supply is required for a gas heat transfer oil furnace. Before use, check if the gas pipeline is unobstructed and the gas valve is open to ensure normal gas supply. - Heat Transfer Oil Circulation: The heat transfer oil furnace needs to circulate the heat transfer oil to the heat source equipment through a circulating pump. Before use, inspect the pump's operation to ensure it is working properly. - Temperature Control: A gas heat transfer oil furnace usually requires a temperature control system to regulate the heat transfer oil's temperature. Before use, check the system's settings and adjustments to ensure accurate and reliable temperature control. - Regular Maintenance: Gas heat transfer oil furnaces require regular maintenance and upkeep, including cleaning burners, inspecting pipeline and valve seals, and replacing worn parts. Regular maintenance ensures the equipment operates normally and extends its lifespan. - Environmental Protection: Gas heat transfer oil furnaces produce exhaust gases during combustion, and exhaust emissions must be ensured. Appropriate exhaust gas treatment measures, such as flue gas purification equipment, can be taken to minimize environmental impact. The above are some points to note when using a gas heat transfer oil furnace. To ensure safety and the normal operation of the equipment, it is recommended to follow relevant operational procedures and safety requirements, and to conduct regular maintenance and inspections. If necessary, consult the manufacturer or engineer of the gas heat transfer oil furnace.

When addressing issues with gas boilers during the heating process, consider the following aspects: - Check gas supply: Ensure the gas supply is normal and inspect the gas pipes for blockages or leaks. If any issues are found, repair or replace the gas pipes promptly. - Clean burners and combustion chambers: Regularly clean the burners and combustion chambers to remove accumulated soot and dirt. This improves combustion efficiency and reduces gas waste. - Check and adjust the ratio of gas to air: Ensure the gas-to-air ratio is appropriate for optimal combustion. An incorrect ratio can lead to incomplete combustion or excessive exhaust. - Check and clean heat exchangers: Regularly inspect and clean heat exchangers to remove soot and dirt. This enhances heat exchange efficiency and ensures heat is effectively transferred to the heating system. - Check and maintain circulating pumps and valves: Ensure the pumps and valves operate correctly to allow smooth flow of hot water or steam through the heating system. - Check and maintain control systems: Ensure the control system of the gas boiler operates properly, allowing for accurate control of parameters such as temperature, pressure, and flow. If issues arise, repair or replace the controller promptly. - Regular maintenance: Perform regular maintenance on the gas boiler, including cleaning, lubricating, and tightening bolts, to extend its lifespan and reduce the occurrence of malfunctions. - Training and awareness: Provide staff training to enhance their awareness and skills in operating and maintaining gas boilers. Employee knowledge and skill improvement aids in effective management and problem-solving during the heating process. - If the issue cannot be resolved or poses safety

During the operation of a thermal oil furnace, several important points should be noted: - Temperature Control: Throughout the operation, the temperature of the thermal oil must be closely monitored and controlled. Ensure it stays within a safe range to avoid decomposition due to excessive heat or condensation and scaling at low temperatures. Regularly inspect and calibrate the temperature sensors to ensure accurate temperature readings. - Pressure Control: Maintain an appropriate working pressure during the operation of the thermal oil furnace. Excessive pressure can lead to equipment damage or leaks, while insufficient pressure can decrease heat transfer efficiency. Regularly inspect and maintain the pressure gauge and safety valve to ensure accurate and safe pressure control. - Oil Quality and Cleanliness: The quality and cleanliness of the thermal oil are crucial for the normal operation of the furnace. Regularly inspect and replace the thermal oil to ensure it meets quality and performance requirements. Regularly clean and maintain components such as heat exchangers, burners, and flues to prevent the accumulation of dust and debris that can affect heat transfer efficiency. - Regular Maintenance and Inspection: The thermal oil furnace requires regular maintenance and inspections to ensure proper operation and extend its lifespan. Regularly inspect and clean burners, flues, heat exchangers, and check and replace seals and valves. Inspect and calibrate safety devices to ensure equipment safety and reliability. - Safe Operation: Strict adherence to operating procedures and safety protocols is necessary during the operation of the thermal oil furnace. Operators must possess relevant skills and knowledge.
Shandong Zhongjie Special Equipment, welcome customers to visit our factory for business discussions.